HAPP27

Hoist HAPP27 5T 4 Post Hoist Car Lift

$5,800.00

GST INCLUSIVE AND COMES WITH A FIVE YEAR STRUCTURAL WARRANTY.

This hoist is designed, tested  and verified to Australian standards at 5T SWL by Queensland professional engineers. The verified design is registered with WH&S for workshop use.

These hoists are typically $9,000 for similar or lesser quality.  We can provide installers in most States or assist you on the initial installations.  A comprehensive installation and operation manual has been prepared by HAPP that details all the installation and operation of the hoist.

STOCK DUE SEPT 2026, LIMITED PRODUCTION

Available on backorder

Options

JB60 Air Pneumatic Jacking Beam (for Happ27)

WH&S Kit

3 Phase Full Pump Assembly Upgrade

All our hoists go out with single phase 240v pump assemblies.  If you want your hoist to be run by 415v, you just need to pay an additional $150 and we can swap it over for you.

GST INCLUSIVE AND COMES WITH A FIVE YEAR STRUCTURAL WARRANTY.

They are a RIGID 5T lift as they can be used to provide wheel alignments on vehicles with the add on wheel alignment kit. As such this lift will not move at all when loaded so the wheel alignments can be done accurately.

All internal welds are inspected by external quality assurance engineers before powder coating.

Features

  • Single point safety release control all four columns simultaneously
  • Cross beam 130mm 10mm i beam
  • Runway – 3 x 100mm 10mm C section beams under checker plate
  • Columns – 5 mm thickness
  • Base plate – 16mm
  • Industrial strength load ramp and end plates
  • Slave runway is movable allowing for narrow and extra wide vehicles
  • Plastic powder coat finish
  • Ultra strong frame and columns
  • Full Australian engineering structural analysis & design
  • Australian standards approved and WH&S registered
  • Full WH&S maintenance program available with WH&S kit
  • Release all column safeties, raise and lower from single point
  • Ratchet safety at with 150mm increments
  • Max runway height 1920mm
  • Lockout pins for extended vehicle storage
  • Removable 855x492mm on ramps
  • HAPP ultra strong 12.5mm thick all steel lift cables tested in NATA registered lab.
  • Tru-bolt anchor bolts for solid mounting
  • High steel grade rugged construction – a) 5mm column, b) 127mm I beam cross beam, c) 3x120mm C section beams under each runway d) Checker plate runway surface e) Approved cable / cylinder / safety system
  • Connector to external limit switch on motor
  • 5 year structural warranty, 12 month manufacturer parts warranty see happ.com.au/warranty

Optional extras items:

  • Wheel alignment kit
  • air pneumatic jacking beam (JB60)
  • Wheel alignment kit (false floor)
Important: EVERY HAPP car lift design is tested in Queensland by Australian Professional engineers against Australian Standards using state of the art technology!!!! The multi coloured pictures on our lift specs are snippets from the engineers report that PROVES that we are doing this. We are the leaders in quality, if you do not see this drawing on your product, it is NOT tested to Australian Standards.
Download Spec Sheet

Contact Us

About Happ HAPP is a Company created by car enthusiasts for car enthusiasts. Car clubs asked us to change the game and we did. We take our job seriously and will only offer you the best products that we can source. We have sold hoists all across Australia. Our prices are the best, with quality and service assured.


I just purchased a HAPP25 4-post hoist (and an oil drain B75L) from Maree and Gavin for my home workshop as I am restoring 2 old British cars (yes I’m crazy). After months of looking around the net I found the HAPP web site had what I wanted and had t... HAPP25 – 4 post hoist – Frank Ragonese – August 1, 2014



Awesome people to deal with and excellent after sales service, wouldn’t deal with anyone else. Very happy customer! HAPP60 – Clear floor hoist – Stephen Ferrais – February 19, 2018


Read More Reviews

Weight 1689 kg
Dimensions 520 × 104 × 53 cm
Load Capacity

5000kg

Lifting Height

1920mm

Overall Height

2277mm

Overall Width

3195mm

Overall Length

5093mm (outter columns base)
5028mm (outter column beam)

Width between pillars

2885mm

Drive through

2748mm TBC

Min pad height

150mm

Net weight

1689kg

CE approved Hydraulic Power Pack

Yes

Motor Capacity

240V, Single phase or 3 Phase 415V (3 phase is an additional $150.00)

Power of motor

2.2kw

Single point safety release control all four columns simultaneously

Yes

Cross beam 130mm 10mm I beam

Yes

Runway

3 x 100mm 10mm C section beams under checker plate

Columns

5 mm thickness

Base plate

16mm

Industrial strength load ramp and end plates

Yes

Slave runway is movable allowing for narrow and extra wide vehicles

Yes

Plastic powder coat finish

Yes

Download Spec Sheet

Contact Us

About Happ HAPP is a Company created by car enthusiasts for car enthusiasts. Car clubs asked us to change the game and we did. We take our job seriously and will only offer you the best products that we can source. We have sold hoists all across Australia. Our prices are the best, with quality and service assured.


Great service and great product. Would highly recommend them Happ90 2 post 3T portable hoist – Rob Cutajar, May 2021



Great to deal with, products are great too. Bought a two post clear floor hoist about 5 years ago still going great. HAPP60 – 1900mm lift – Leon Hansen – October 7, 2019


Read More Reviews

  • We are an Australian owned and operated company with a focus on the best possible quality for reasonable prices.
  • We sell mainly by recommendation. To do this we  have personal and professional customer service;  we work with every customer to make sure they are happy with the products they purchase.
  • Imported products are typically assembled overseas to keep the costs down. We  have a Qualified Mechanical engineer working for us in China and other engineering inspection companies engaged that inspect our products and partner companies’ quality processes. Inspections typically take place early in production including internal components which are reworked if not up to standard. Critical components are focused on to ensure key products are made correctly.
  • We also use the best possible materials in our products. Our clear floor hoists have stainless steel hydraulic lines and our four post hoists have 12+mm solid steel cables tested in Australian NATA registered laboratories. Our synchronisation cables are solid steel and safety latches are billet steel.
  • We apply the best designs from our business registered hoists into our home use hoists.  For example, all arms on the two post hoists have the 4T updates, and carriages have the bracing update specified by Australian Engineers for our business hoists.
  • We offer an ever increasing range of workshop items allowing customers to source extra items at low cost, many of these items are half the cost of other suppliers – just ask us to email you our catalogue.
  • This hoist is erected in Ormeau for you to view before placing an order.
Download Spec Sheet

Contact Us

About Happ HAPP is a Company created by car enthusiasts for car enthusiasts. Car clubs asked us to change the game and we did. We take our job seriously and will only offer you the best products that we can source. We have sold hoists all across Australia. Our prices are the best, with quality and service assured.


Looked around to find the best bike hoist that would be able to fit a raked Harley Davidson, 2400mm long bike, this was the best hoist and the only one I found that was 2200mm long the MC 30 , it was so easy buy, the staff where amazing and so helpful,... MC30 2200mm table Motorbike Lift – Robbie V, May 2026



Gary D recommends Happ Car Hoists – Facebook review


Read More Reviews