HAPP45P-1

Hoist HAPP45Pi 4.5T , 2 Post Direct drive Electric, inverted cylinder – Hydraulic Lift

$4,290.00

GST INCLUSIVE AND COMES WITH A THREE YEAR STRUCTURAL WARRANTY.

The HAPP 45P provides a huge 4.5T lift capacity with a high 3.729 height to the safety bar which can be extended with 300 or 600mm extensions.

The lift uses direct drive cylinders (no chains) which reduces the number of moving parts, the inverted long cylinders have the rod on the bottom and push on the base of the carriage with cylinder casing. This minimised chance of  water ingress extending seal life. If you are doing welding or grinding under vehicles look at HAPP 45P.

The arms are the latest Generation 2 design, arms and carriage use higher grade steel for extra load rating.  Good for workshops and project / race car users who will use the lift frequently and have a wide variety of vehicles to lift including 4WDs with uneven load distribution.  You can load small / light vehicles from either direction, medium weight and larger vehicles can be loaded from both directions by swapping arms from front to back.

Options

WH&S Kit

45P/Pi 300mm Extension Kit

45P/Pi 600mm Extension Kit

Stabiliser Bars E4

GST INCLUSIVE PLUS POSTAGE

The HAPP E4 stabilizer bar provides extra front to back stability for HAPP hoists.

These are sold as a set of TWO.

Large Base Floor Plate

GST INCLUSIVE AND INCLUDING THE BOLTS REQUIRED PLUS POSTAGE

The large base plate is exactly that… A big base plate for HAPP hoists. 2 will be sent each time.

If you are concerned about the ability of your concrete to support a Happ hoist this accessory may be the answer. The plate measures a whopping 700 x 700mm extending the contact area of the hoist by almost 4 times spreading the load over this large area.

3 Phase Full Pump Assembly Upgrade

G2S Generation2 2x 2pc Short Arms

G2L Generation2 2x 2pc Long Arms

SKU: HAPP45P-1 Categories: , ,

THIS HOIST IS GST INCLUSIVE AND HAS A FIVE YEAR STRUCTURAL WARRANTY

HAPP45Pi 4.5T, 2 Post Direct drive Electric, inverted cylinder – Hydraulic Lift

This hoist is designed, tested  and verified to Australian standards at 4T SWL by Queensland professional engineers. The verified design is registered with WH&S for workshop use.

Other features for this lift are:

  • The lift uses direct drive cylinders (no chains) which reduces the number of moving parts. As the cylinder seals are on the bottom the seals are more resistant to moisture, this is not an issue typically but if you wash a car down or spray water on the lift, this is a better choice for you than our other hoists.
  • The HAPP 45Pi provides a huge 4.5T lift capacity with a high 3.729m height to the safety bar, making it easier to lift tall vehicles with standard one piece columns.
  • Australian Standards Tested and Certified in Queensland by RPEQ engineers
  • Robot welded Asynchronous Gen 2 Arms, Column and Carriage
  • 2 limit switches, one for over height as most clear floor lifts and a second inside the column to halt hydraulics before cylinder reaches full length avoiding over pressure scenarios extending cylinder seal life.
  • Robot folded Column
  • Direct drive cylinders – less moving parts, better for those welding and grinding under vehicle
  • CNC controlled laser, milling and water jet cutting machined parts
  • Ready for use in businesses, Workplace Health and safety registration kit available
  • Release both column safeties from single point
  • Control cables, hoses routed overhead
  • Over height protection with limit switch on top cross bar
  • Cylinder over pressure protection with limit switch inside column
  • Carriages move synchronously, Dual Hydraulic cylinder drive, stable lifting and lowering
  • Structurally tested in Queensland on computer simulation with 125% of rated capacity and static test with 150% of rated capacity by HAPP to Australian Standards
  • Australian and New Zealand Standards AS/NZS designed, tested and certified
  • 5mm thick columns, 16 mm thick base plate, 20mm Tru-bolt design anchor bolts
  • HAPP two stage Screw up drop in pad design give best of drop in  using spacers and screw up pad design
  • Australian Standards tested arm locks, 3” + 6” spacers standard
  • Double insulated wiring  with 4amp fuse and plugs for all limit switch wiring exceeding Australian Standards requirements
  • M20 160mm Tru-bolt anchor bolts standard
  • Industrial 15amp plug on 1m lead standard
  • The 45Pi uses ISO 32 grade hydraulic oil in its direct drive cylinders.
  • 5 year structural warranty , 12 month manufacturer parts warranty see happ.com.au/warranty

FREE low profile car ramps provided with all our 2 post car hoists.

Important: EVERY HAPP car lift design is tested in Queensland by Australian Professional engineers against Australian Standards using state of the art technology!!!! The multi coloured pictures on our lift specs are snippets from the engineers report that PROVES that we are doing this. We are the leaders in quality, if you do not see this drawing on your product, it is NOT tested to Australian Standards.
Download Spec Sheet

Contact Us

About Happ HAPP is a Company created by car enthusiasts for car enthusiasts. Car clubs asked us to change the game and we did. We take our job seriously and will only offer you the best products that we can source. We have sold hoists all across Australia. Our prices are the best, with quality and service assured.


Just got my new Happ25 installed, very nice lift guys thanks Happ! HAPP25 – Jemele Deen – 4 post 4T business approved – January 8, 2019



Using HAPP hoists in our our workshop since 2015. Still going strong. Used every day. TC20/WB20 combo – tyre machines – Ashley Gibbons – June 18, 2018


Read More Reviews

Weight 786 kg
Dimensions 385 × 50 × 74 cm
Lifting Capacity

Aus Std SWL 4500kg

Lift Height

1920–2120mm (with pads)

Min pad height

100mm

Overall height

3904mm

Overall Width

34300mm

Width between pillars

2850mm

Lifting Time

40-70s

CE approved Hydraulic Power Pack

Yes

Motor Power

2.2kw

Plastic powder coat finish

Yes

Power Supply

3-415v/50hz 1-240v/50hz15Amp

Power oil pressure

20Mpa

Gross weight

720kgs

Net Weight

689kg

Download Spec Sheet

Contact Us

About Happ HAPP is a Company created by car enthusiasts for car enthusiasts. Car clubs asked us to change the game and we did. We take our job seriously and will only offer you the best products that we can source. We have sold hoists all across Australia. Our prices are the best, with quality and service assured.


A note to say thanks for the way you do business, a pleasure. Very pleased with the hoist. Extremely well made and went together without a problem. Would recommend your business and your product to anyone. Regards Wayne HAPP40 – Business approved – Clear floor – Wayne Hook – June 27, 2016



I have now purchased two hoists from Happ. The first being a 2 poster roughly 6 years ago and the second being a 4 poster roughly a week ago. Their products and service are of a high quality and their delivery/pick up is a no fuss, hassle free experience. 4T Happ25 4 post hoist – Lee M, Jun 2024


Read More Reviews

  • We are an Australian owned and operated company with a focus on the best possible quality for reasonable prices.
  • We sell mainly by recommendation. To do this we  have personal and professional customer service;  we work with every customer to make sure they are happy with the products they purchase.
  • Imported products are typically assembled overseas to keep the costs down. We  have a Qualified Mechanical engineer working for us in China and other engineering inspection companies engaged that inspect our products and partner companies’ quality processes. Inspections typically take place early in production including internal components which are reworked if not up to standard. Critical components are focused on to ensure key products are made correctly.
  • We also use the best possible materials in our products. Our clear floor hoists have stainless steel hydraulic lines and our four post hoists have 12+mm solid steel cables tested in Australian NATA registered laboratories. Our synchronisation cables are solid steel and safety latches are billet steel.
  • We apply the best designs from our business registered hoists into our home use hoists.  For example, all arms on the two post hoists have the 4T updates, and carriages have the bracing update specified by Australian Engineers for our business hoists.
  • We offer an ever increasing range of workshop items allowing customers to source extra items at low cost, many of these items are half the cost of other suppliers – just ask us to email you our catalogue.
  • This hoist is erected in Ormeau for you to view before placing an order.
Download Spec Sheet

Contact Us

About Happ HAPP is a Company created by car enthusiasts for car enthusiasts. Car clubs asked us to change the game and we did. We take our job seriously and will only offer you the best products that we can source. We have sold hoists all across Australia. Our prices are the best, with quality and service assured.


Thought I’d drop you a line to thank you for the great product, prompt delivery and exceptional pre and after purchase service regarding my HAPP 30 hoist. All my questions were answered in a thorough and friendly manner, making for a very pleasa... HAPP30 – 2 post floor plate 4T hoist – Michael Shuttleworth – September 13, 2012



I recently purchased a new 1.5T aluminium trolley jack and a 1T engine crane with pneumatics. Jodie and Karen were fast and efficient with getting me sorted out and answering questions, and pick up in Willow Vale was great. Gavan was also super helpful... Engine Crane EC10A & Trolley Jack ATJ10 – Chris Lee, March 2023


Read More Reviews